Trinket - Mini Microcontroller module - 5V - Adafruit 1501

Bestseller

Product Code:: 53916244

Trinket - Mini Microcontroller module - 5V - Adafruit 1501

49 GEL

Brand Adafruit
Shipping from Poland
Post delivery June 13
Shipping cost for orders to Georgia from GEL 174

Properties

UC - I2C: yes
UC - UART: yes
UC - ядро: 1. Single Core
Voltage To: 5.0 V
Voltage From: 5.0 V
UC - SPI Interface: yes
Выходное напряжение от: 5.0 V
Выходное напряжение до: 5.0 V

General characteristics

UC - A/C: 10-bit
UC - RAM: 0,5 kB
UC - PWM: 2
UC - USB: miniUSB
UC - ядро: 8-bit AVR
UC - EEPROM: 0,5 kB
UC - Вспышка: 8 kB
UC - аналог в: 1
UC - frequency: 8 MHz
UC - microcontroller: Attiny85
UC - Цифровые контакты: 5

Other features

Brand: Adafruit
Nominal output voltage: 5.0 V

Power

Rated voltage: 5 V

Description

Description: Adafruit Trinket - Mini Microcontroller module - 5V

Miniature module with an AVR Attiny85 microcontroller and is equipped with 8 KB of Flash memory, 5 digital pins, analog input and 2 PWM channels. On board is miniUSB connector, through which the system can be programmed via the Arduino IDE using the cable. After only a few minor changes, the board behaves like a standard Arduino.

The presentation of the Adafruit Trinket board's possibilities.

Choose the right board

In our offer, you will find two versions of the Adafruit Trinket - 3.3 V and 5.0 V. Both modules work in the same way, differing only in the operating voltage of the logic leads and maximum clock frequency. The 3.3 V version runs at a frequency of 8 MHz, 5.0 V and works with 8 MHz and 16 MHz.

Check how to program the Adafruit Trinket using the Arduino IDE or AVRdude!

The collaboration with Arduino

The device can be programmed via the Arduino environment, however, due to the small size of the board, there are some differences:

Trinket has no serial port and the serial monitor embedded in the environment of Arduino, will not work.
Computers equipped with USB 3.0 ports can have a problem with the recognition of the Trinket bootloader, the solution to this situation is to use an external USB 2.0 hub.
The board is working with Windows and Mac OS, at the moment, there are no drivers for Linux.

Specification

The AVR Attiny85 microcontroller:
- Flash memory: 8 KB (2.75 kb of which is occupied by the bootloader)
- SRAM: 512 b
- EEPROM: 512 bytes
- Clock Frequency: internal 8 MHz with the possibility to set 16 MHz for 5 V version
USB bootloader with the possibility of programming via AVRdude or via Arduino IDE
MicroUSB connector for programming, in our assortment you will find the necessary wire
Installed voltage regulators of 5.0 V and 3.3 V with current delivery up to 150 mA, allow to connect the supply voltage up to 16 V.
Power supply from USB port or external power source with automatic switching system
On the board are two LEDs: green for power, and red for the user, connected to pin 1.
5 digital pins of I/o, including:
- 2, together with the USB interface
- 1 analog input
- 2 PWM channels
- I2C and SPI interface
Works with most basic libraries of the Arduino including Adafruit Neopixel.
Four mounting holes with diameter of 2.1 mm
Dimensions: 31 x 15.5 x 5 mm
Weight: 1.85 g