Properties
- UC - I2C
- yes
- UC - USB
- microUSB
- UC - PWM
- 6
- UC - UART
- yes
- UC - ядро
- 8-bit AVR, 1. Single Core
- Voltage To
- 6.0 V
- UC - Разъем
- 5V microUSB
- UC - аналог в
- 8
- UC - frequency
- 20 MHz
- UC - SPI Interface
- yes
- Выходное напряжение до
- 5.0 V
- UC - Цифровые контакты
- 14
- Выходное напряжение от
- 3.3 V
Design
- Product Type
- Запчасть для микрокомпьютера
General characteristics
- UC - RAM
- 6 kB
- UC - EEPROM
- 256 B
- UC - Вспышка
- 48 kB
- Voltage From
- 21.0 V
- UC - microcontroller
- ATmega4809
Other features
- Brand
- Arduino
Power
- Nominal output voltage
- 5.0 V
Description
A version of the popularArduino Nanotile. Every model is based onATMega4809 AVRprocessor with 20 MHz clock, equipped with 48 kB flash memory and 256 B EEPROM. The user has30 pins,15 on each side. The ATSAMD11D14A microcontroller is responsible for communication with PC.The board has dimensions 45 x 18 mm.
Offered board has soldered in leads. In our offer we also have a version without connectors.
Arduino Nano Every.
Programming and possibilities of Arduino Nano Every.Arduino Nano Every can be programmed viaArduino IDE, both onlineand offline.Microcontroller ATSAMD11D14Aworks asUSB - UART converter. On the 30 pins you can findGPIO, SPI, I2C, PWM, USART, DAC and ADCamong others. Power and RESET pins are also available.
Arduino Nano Every output.
Main features of Arduino Nano EveryNano user has 14 digital pins, 6 PWM outputs and 8 analog pins available. Arduino Nano Every can be powered via microUSB port with 5 V or via V in with 6 V to 21 V.
Pin Designation Type Description 1 D13 Digital SPI, SCK, GPIO 2 + 3V3 Power output Power supply for external devices 3 AREF Analogue Reference pin, can be used as GPIO 4 A0 / DAC0 Analogue ADC input / DAC output, canbe used as GPIO 5A1
Analogue ADC input,canbe used as GPIO 6 A2 Analogue ADC input,canbe used as GPIO 7 A3 Analogue ADC input,canbe used as GPIO 8 A4 / SDA Analogue ADC input,canbe used as GPIO 9 A5 / SCL Analogue ADC input,canbe used as GPIO 10 A6 Analogue ADC input,canbe used as GPIO 11 A7 Analogue ADC input,canbe used as GPIO 12 +5 V Power output Power supply for external devices 13 RST Digital input Active reset 14 GND Power supply Mass 15 VIN Power supply Power supply 16 TX Digital USART TX,canbe used like GPIO 17 RX Digital USART RX,canbe used like GPIO 18 RST Digital Active reset 19 GND Power supply Mass 20 D2 Digital GPIO 21 D3 / PWM Digital GPIO,canbe used like GPIO 22 D4 Digital GPIO 23 D5 / PWM Digital GPIO,canbe used like GPIO 24 D6 / PWM Digital GPIO,canbe used like GPIO 25 D7 Digital GPIO 26 D8 Digital GPIO 27 D9 / PWM Digital GPIO,canbe used like GPIO 28 D10 / PWM Digital GPIO,canbe used like GPIO 29 D11 MOSI Digital SPI MOSI,canbe used like GPIO 30 D12 / MISO Digital SPI MISO,canbe used like GPIO Specifications of Arduino Nano Every- Supply voltage: 6 V to 21 V
- Microcontroller: ATMega4809
- Clock: 20 MHz
- Flash memory: 48 kB
- SRAM 6 kB
- EEPROM 256 B
- Digital pins: 14
- PWM pins: 6
- Analogue pins: 8
- MicroUSB socket
- Interfaces: GPIO, SPI, I2C, USART, PWM
- Transducers: ADC, DAC
- Dimensions: 45 x 18 mm
- Manufacturer's website
- User guide
- Arduino Forum
- Installation and first start-up
- Arduino IDE software
- Module diagram
- Eagle files
- ATmega328 documentation
- ATSAMD11D14A documentation