Soldering station hotair and tip-based WEP 992D+ FAN remembers settings + fan in iron - 720W

Bestseller
47170576
585 GEL
  • Brand WEP
  • Shipping from Poland
  • Post delivery July 11
  • Shipping cost for orders to Georgia from GEL 178

Properties

Voltage To
220 V AC
Voltage From
240 V AC
Паяльник - Вентилятор
yes
Припой - Горячий воздух
yes
Кондиционер паяного типа
Цифровой
Припой - показания реальной температуры
yes

Features

Temperature
200 - 480 °C

Other features

Brand
WEP

Power

Rated power
720 W
Rated voltage
230 V AC

Description

Description

Soldering iron WEP 992D+ FAN is a hotair soldering station and a tip-based soldering iron (75 W), used for soldering and desoldering electronic components. The station is equipped with microprocessor with precise PID controller, which checks the operating parameters and adjusts them to the preset values.

 

Models 992D+ are characterized by:
  • 3 work programmes - station has the ability to memorize 3 of the work programmes for hot air and tip iton. Depending on the type of works (assembly or disassembly) you must install an appropriate program.
  • Operation of hot air in automatic and manual mode:
    • automatic- when you put down the iton, the system will turn off the heat and cool the iton to a safe temperature
    • manual- when you put down the iron, the system further heats up a heating element before finishing, it is recommend you go to auto mode.
  • The function of temperature correction depending on external parameters
  • Mode C/Fthe ability to change the units in which temperature is displayed.
  • Sleep function of soldering iron tip-based - if the iron is not used the given time interval (0 - 99 minutes) the system switches to sleep mode, that is cooled to a temperature of 200 °C, which ensures long service life of the device.
  • Tip-based soldering iron with a heating element, it heats up very fast, has a stable temperature, which is electrostatically safe.

 

 

Specification
  • Voltage: 220 - 240 V / 50 Hz (network)
  • Power consumption: 720 W
  • The station is controlled through a microcontroller that provides high stability
  • The device has a PID controller
  • Compact design with large and clear LCD display

 

  • Soldering Iron Hotair:
    • Blowing air through the fan in the hotair iron
    • Smooth adjustment of temperature in the range
    • Adjustable temperature hot air from 100 °C to 480 °C
    • Temperature stability: +/-1 °C
    • LCD display showing actual power supply
    • Operation mode manual / automatic
    • Protection before reaching the high temperature and inform the alarm
    • Cable length of the bulb: up to 90 cm

 

  • Soldering Iron Tip-based
    • Iron 907I
    • Adjustable temperature soldering tip: 200 °C to 480 °C
    • Temperature stability: +/- 1 °C
    • Peak power of soldering iron: from 72 to 75 W
    • The resistance to grounding: up to 2 Ω
    • Capacity in relation to protective earth: up to 2 mV
    • The system is ESD safe
    • Cable length of the iron: up to 100 cm
    • Sleep mode: enabled after idle operation 0-99 minutes

 

Includes:
  • Station WEP 992D+ FAN
  • Hotair iron stand
  • Set of nozzles:
    • round with a diameter of 4.4 mm
    • round, diameter 6 mm
    • round diameter of 9 mm
    • square 12x12 mm
  • Soldering iron stand along with a cleaning sponge
  • Soldering iron 907I with tip T-B
  • A gripper for lifting circuits
  • Power cable

 

Firstrun

  • You should not run the device immediately after delivery.
  • Equipment must remain for about 12 hours at room temperature before switching on.
  • All complaints caused by running of the equipment too soon will be denied.
  • You must completely remove the screw/screws from the bottom of the station if the compressor is the source of air supply. These screws are marked in red (1 or 3 screws depending on model).

 

Note

Heating elements (heaters) and tips are not subject to warranty, you should purchase new ones.

 

Our range of accessories for soldering:
  • soldering tin of various diameters
  • fluxes and rosins
  • braids to remove excess tin
  • suckers
  • soldering tips
  • tweezers, holders, magnifying glass
  • sponges and cleaners