VICTRON ENERGY Multiplus-II 48/5000/70-50 Charger
Bestseller
- Product Code:
- 108375479
6,245 GEL
Properties
Features
- Color
- Blue
Other features
- Brand
- Victron Energy
Description
Victron Phoenix 12/800 VE.Direct Schuko is responsible for extracting the energy stored in the batteries connected to it and converting it into single-phase current suitable for consumption.
This Pure Wave Inverter Victron Phoenix 12/800 VE.Direct Schuko requires batteries that correspond to their nominal working voltage to operate the Victron brand is a leader in the development of inverters for all types of uses in addition to their nominal power, Victron inverters offer additional starting power to cope with occasional consumption peaks.
This inverter manufactured in Holland has an efficiency of 90% and a quality that is reflected in its 5-year warranty.
General features:
VE.Direct communication port the VE.Direct port can be connected to:
A computer (VE.Direct to USB interface cable required).
Apple and Android smartphones, tablets, mackbooks and other devices (VE.Direct to Bluetooth Smart dongle required).
Fully configurable:
Alarm trigger levels and low battery voltage reset.
Low battery voltage disconnect and reset levels.
Dynamic disconnection:
load dependent disconnection level.
Output voltage 210 - 245V.
Frequency 50 Hz or 60 Hz.
ECO mode on/off and ECO mode level sensor Monitoring:
Input/output voltage and current, % load and alarms.
High starting power.
Required for starting loads such as converters for LED lamps, halogen lamps or power tools.
ECO mode in ECO mode.
The Inverter will go into standby when the load drops below a preset value (minimum load:
15W).
predetermined value (minimum load:
15W).
Once in standby.
The Inverter will activate briefly (adjustable.
default:
every 2.5 seconds).
If the load exceeds the preset level.
The Inverter will remain on.
Remote on/off switch.
A remote On/Off switch can be connected to a two-phase connector or between the battery positive and the left contact of the two-phase connector LED diagnostics.
Please refer to the manual for description.
For transferring the load to another AC source:
the automatic transfer switch.
For our lower power inverters we recommend our Filax automatic transfer switch.
Filax automatic transfer switch the switching time of the ´Filax´ is very short (less than 20 milliseconds), so that computers and other electronic equipment.
computers and other electronic equipment will continue to operate without interruption.
Screw terminals.
No special tools required for installation.
This Pure Wave Inverter Victron Phoenix 12/800 VE.Direct Schuko requires batteries that correspond to their nominal working voltage to operate the Victron brand is a leader in the development of inverters for all types of uses in addition to their nominal power, Victron inverters offer additional starting power to cope with occasional consumption peaks.
This inverter manufactured in Holland has an efficiency of 90% and a quality that is reflected in its 5-year warranty.
General features:
VE.Direct communication port the VE.Direct port can be connected to:
A computer (VE.Direct to USB interface cable required).
Apple and Android smartphones, tablets, mackbooks and other devices (VE.Direct to Bluetooth Smart dongle required).
Fully configurable:
Alarm trigger levels and low battery voltage reset.
Low battery voltage disconnect and reset levels.
Dynamic disconnection:
load dependent disconnection level.
Output voltage 210 - 245V.
Frequency 50 Hz or 60 Hz.
ECO mode on/off and ECO mode level sensor Monitoring:
Input/output voltage and current, % load and alarms.
High starting power.
Required for starting loads such as converters for LED lamps, halogen lamps or power tools.
ECO mode in ECO mode.
The Inverter will go into standby when the load drops below a preset value (minimum load:
15W).
predetermined value (minimum load:
15W).
Once in standby.
The Inverter will activate briefly (adjustable.
default:
every 2.5 seconds).
If the load exceeds the preset level.
The Inverter will remain on.
Remote on/off switch.
A remote On/Off switch can be connected to a two-phase connector or between the battery positive and the left contact of the two-phase connector LED diagnostics.
Please refer to the manual for description.
For transferring the load to another AC source:
the automatic transfer switch.
For our lower power inverters we recommend our Filax automatic transfer switch.
Filax automatic transfer switch the switching time of the ´Filax´ is very short (less than 20 milliseconds), so that computers and other electronic equipment.
computers and other electronic equipment will continue to operate without interruption.
Screw terminals.
No special tools required for installation.
