WEP 992DA+ hotair and soldering station + saving settings + fume extraction + compressor - 720W

Bestseller
47446553
874 GEL
  • Brand WEP
  • Shipping from Poland
  • Post delivery July 11
  • Shipping cost for orders to Georgia from GEL 178

Properties

Voltage To
220 V AC
Voltage From
240 V AC
Лаборатория будущего
Compatible
Паяльник - Вентилятор
No

Basic information

Rated power
720 W

Features

Temperature
200 - 480 °C

General characteristics

Припой - Горячий воздух
yes
Кондиционер паяного типа
Цифровой
Припой - показания реальной температуры
yes

Other features

Brand
WEP

Power

Rated voltage
230 V AC

Description

Description

Device WEP 992DA+ is the soldering station on hotair and a grotto soldering iron (75 W). The device is equipped with a microcontroller with implemented PID controller, which checks the operating parameters and adjusts them to the preset values.

 

Presentation of the soldering station WEP 992DA+.

 

Among other models 992D+, highlighted are:
  • 3 programmes of work- station has the possibility to memorize 3 of the work programme for hot air and the flask. Depending on type of works, on assembly or disassembly, we set the appropriate program.
  • The operation of the hotair in automatic and manual mode:
    • automatic- when you put the flask away, the system will turn off the heat and will cool the flask to a safe temperature
    • manual- when you put the flask away, the system continues to heat a heating element, before finishing the work, it is recommended to switch to auto-mode.
  • The function of temperature correction depending on external parameters
  • Work in C/F mode - the possibility to change the units, in which temperature is displayed.
  • Sleep function for grotto soldering iron- if the flask is not used by the earlier set time (0 - 99 minutes) the system switches it to the sleepmode, that is, cooling it to a temperature of 200°C, which ensures longer service life of the device.
  • Grotto flaskwith a heating element, fast heating up itself, keeping a stable temperature, which is electrostatically safe.
  • Ehaust ventilation -station has the possibility to extract of harmful fumes.

 

 

Specification
  • Power supply: from 220 V to 240 V / 50 Hz (network)
  • Power consumption: 720 W
  • The station is controlled through a microcontroller that provides high stability of work
  • The device has a PID controller
  • Compact design with large and readable LCD display
  • The cooling function

 

  • Soldering Iron Hotair:
    • Blowing of air is through the compressor inside the station
    • Air-flow: up to 28 l/min
    • Smooth adjustment of temperature in the whole range
    • Adjustable temperature of hot air: 100 °C to 480 °C
    • Temperature stability: +/-1 °C
    • LCD display showing actual power of air-flow
    • Manual / automatic operation mode 
    • Protection before reaching too high temperature and informing the alarm
    • Cable with length of the flask: up to 90 cm

 

  • Grotto Soldering Iron 
    • Adjustable temperature of th seoldering tip: 200 °C to 480 °C
    • Temperature stability: +/- 1 °C
    • Peak power of the soldering flask iron: from 72 to 75 W
    • The resistance in relation to grounding: up to 2 Ω
    • Capacity in relation to grounding: up to 2 mV
    • The system ESD safe
    • Cable length of the flask: up to 100 cm
    • Sleep mode: enabled after idle operation for 0-99 minutes

 

Includes:
  • Station WEP 992DA+ with exhaust ventilation
  • Stand the for the hotair flask
  • Set of nozzles:
    • round with a diameter of 2.5 mm
    • round with a diameter of 4.4 mm
    • round with a diameter of 6 mm
    • round with a diameter of 9 mm
    • square 12x12 mm
  • Stand for the grotto flask along with a cleaning sponge
  • The 908B grotto flask with tip T-B with exhaust ventilation
  • A gripper for lifting the chips
  • Power cable

 

First run

  • After delivery of equipment, it should be not immediately started.
  • Equipment must remain about 12 hours at room temperature before switching on.
  • All applications for damages caused by the premature commissioning of the equipment. will be denied.
  • You must completely remove the screw/screws from the bottom of the station if the source of air supply is compressor. These screws are marked in red (1 or 3 screws depending on model).

 

Our range of accessoriesfor soldering:
  • solders - tins of various diameters
  • fluxes and calaphonies
  • braids to remove the excess of tin
  • evacuators
  • soldering tips
  • tweezers,holders, magnifiers
  • sponges and cleaning cloths