Module LTE/GSM - u-GSM shield v2.19 EG91E - for Arduino and Raspberry Pi - u.FL connector

Бестселлер
42763942
-15%
11 208 ₽
Старая цена 13 144 ₽

Мы выстраиваем выгодные партнерские отношения с поставщиками электроники Itbrain Power и отобрали для вас лучших производителей брендовых товаров из Европы, Америки, Турции и ОАЭ, специализируясь на аутлетах и дискаунтерах. Прямая доставка из-за рубежа до покупателя нашими логистическими решениями — это оптимизированные и экономичные решения, вы не переплачиваете в цене товара за расходы на торговые помещения и шоурумы. Заказ будет отправлен напрямую с нашего склада по указанному вами адресу, по цене недоступной для местных магазинов.

Оригинальные брендовые товары в широком ассортименте с вкусными скидками — так можно описать наш интернет магазин. Доставка заказа будет отслеживаться на всех этапах покупки и работает сразу после оплаты заказа.

  • Бренд Itbrain Power
  • Доставка из Польши
  • Пункт выдачи СДЭК 30 мая
  • Стоимость доставки заказа в Россию от 849 ₽

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Прочие свойства

Бренд
Itbrain Power

Описание

Product description: LTE/GSM module - u-GSM shield v2.19 EG91E

Module compatible with Arduino, Raspberry Pi (version 3B+, 3B, 2B, B+ and A+) and BeagleBone Black, which enables communication in LTE / GSM CAT1 standard. It allows to make voice calls and send SMS messages. On the board there are: SIM card connector, charging module for Li-Pol / Li-Ion battery and RESET button. It has connectors for GSM u.FL antennas.

Component layout on the u-GSM shield board.

Pinouts of the LTE/GSM module - u-GSM shield Pin Description STS Status pinout. RI Ring Indicator output. GND System ground. VCC 4V input/output, internally connected to Li-Pol + pad. VIN 5V input for Li-Pol charger. VUSB 5V output. ENA Activation pin, activated by a high state. RST Reset, high state activated. TX Communication via serial interface. RX . Communication via serial interface. Connecting LTE/GSM module to Arduino

The chip works with Arduino Uno using the following pins:

Pin Arduino Description GSM RX D3 Communication via serial interface. GSM TX D2 Communication via serial interface. RESET D6 Reset of the GSM chip. Ena D7 Control voltage of GSM chip (On/Off). VIN (5 V LiPol) 5 V

5 V power supply. Details of connection in case of LiPol batteries are available in manufacturer's manual.

GND

GND System ground.

STATUS

D5 Status pinout. Connecting LTE/GSM module to Raspberry Pi

The module has special breakout connectors that allow direct plugging into the GPIO connectors of the Raspberry Pi or BeagleBone Black.

In order to run the module with Raspberry Pi the following connections need to be made:

Pin RPi Description GSM RX 10

Communication via serial interface, (not connected for USB communication).

GSM TX 08

Communication via serial interface (not connected when using USB).

RESET 18 GSM system reset. ON / OFF 16 GSM system power voltage control (On/Off). VIN (5 V LiPol) 02/04 Supply voltage 5 V.

GND

04/14 GND of the chip. STATUS 12 Status pinout.

Detailed description of the module can be found in the user guide in parts one and two and on the manufacturer's website.

LTE/GSM module specification - uGSM shield
  • Controller: Quectel EG91E
  • Supported standards: LTE / M2M CAT1
  • Frequencies:
    • FDD LTE: B1 / B3 / B7 / B8 / B20 / B28A
    • WCDMA: B1 / B5 / B8
    • GSM: B1 / B8
  • Speeds:
    • LTE-FDD: up to 10 Mb/s (DL) / up to 10 Mb/s (UL)
    • DC-HSDPA: up to 42 Mbps (DL) / HSUPA up to 5.76 Mbps (UL)
    • WCDMA: up to 384 Kbps (DL) / up to 384 Kbps (UL)
    • EDGE/GPRS: up to max. 296 Kbps (DL), max. 236.8 Kbps (UL) / max. 107 Kbps (DL), max. 85.6 Kbps (UL)
  • Nano SIM / micro SIM connector
  • Antenna connectors u.FL
  • Built-in USB-UART converter (USB connector can be used to power the module)
  • Automatic selection of logic levels from 3 V to 5 V
  • Reset button
  • Works with Arduino, Raspberry Pi and BeagleBone Black along with manufacturer's sample codes
  • Two mounting holes with diameter: 2.5mm
  • Board dimensions: 45 x 27 mm
Useful links
  • Manufacturer homepage
  • User guide 1
  • User'sGuide 2 - interfacing with RaspberryPi
  • User's Guide 3 - interfacing with BeagleBone Black
  • u-GSM modules presentation
  • Quectel EG91E module documentation

Доставка

Доставим товар из Германии от поставщика DESTE FZ LLC курьерской службой, в отделение Почты или пункт выдачи в вашем городе. Доставка в Армению, Казахстан, Грузию и Киргизию будет осуществлена доступными службами. Вы сможете выбрать желаемый способ доставки заказа в момент его оформления. Стоимость доставки зависит от выбранного вами метода и составит от 849 руб. Заказ будет доставлен за 10-30 дней, срок зависит от выбранного города. Если вы закажете этот товар прямо сейчас, доставим его 19 мая - 8 июня.

Доставка электроники Itbrain Power напрямую из Германии в Москву, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие города России осуществляется надежными и проверенными нами службами доставки.

Как только заказ будет отправлен к вам с нашего склада, отслеживание заказа по номеру посылки станет доступным.