LSM6DS3TR-C + LIS3MDL 9DOF IMU - accelerometer, gyroscope and magnetometer I2C - Adafruit 5543

Бестселлер
55529810
3 947 ₽

Мы выстраиваем выгодные партнерские отношения с поставщиками электроники Adafruit и отобрали для вас лучших производителей брендовых товаров из Европы, Америки, Турции и ОАЭ, специализируясь на аутлетах и дискаунтерах. Прямая доставка из-за рубежа до покупателя нашими логистическими решениями — это оптимизированные и экономичные решения, вы не переплачиваете в цене товара за расходы на торговые помещения и шоурумы. Заказ будет отправлен напрямую с нашего склада по указанному вами адресу, по цене недоступной для местных магазинов.

Оригинальные брендовые товары в широком ассортименте с вкусными скидками — так можно описать наш интернет магазин. Доставка заказа будет отслеживаться на всех этапах покупки и работает сразу после оплаты заказа.

  • Бренд Adafruit
  • Доставка из Польши
  • Пункт выдачи СДЭК 5 июня
  • Стоимость доставки заказа в Россию от 838 ₽

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Прочие свойства

Бренд
Adafruit

Описание

Product description: LSM6DS3TR-C + LIS3MDL 9DOF IMU - accelerometer, gyroscope and I2C magnetometer - Adafruit 5543

The sensor is based on the ST LSM6DS3TR-C system, a popular 6-DoF IMU accelerometer with a gyroscope. It allows you to measure acceleration (3-axis accelerometer) and spatial orientation (3-axis gyroscope). There is also a LIS3MDL 3-axis magnetometer on the board, which detects where the strongest magnetic force is coming from, usually used to detect magnetic north. The sensor can be supplied with the voltage of 3 V or 5 V , the same values assume the values of logical voltage. Adafruit 5543 uses I2C communication. It was equipped with the STEMMA QT / Qwiic connector, which makes prototyping much easier.

The product is compatible with Arduino. The manufacturer provides a user manual and a library for Arduino .

LSM6DS3TR-C + LIS3MDL 9DOF IMU - accelerometer, gyroscope and I2C magnetometer .

Presentation of the module prepared by the manufacturer .

Leads located on both sides of the board .

Leads of the Adafruit 5543 module
  • VIN : Power pin (the board has a built-in voltage regulator, it should be powered with the same voltage as the logic level of the microcontroller used)
  • 3Vo : 3.3 V output from the voltage regulator (load capacity up to 100 mA)
  • GND : Ground (common for power and logic)
  • SCL : The clock line of the I2C bus
  • SDA : Data line of the I2C bus
  • STEMMA QT : Connectors that allow the sensor to be connected to development boards with STEMMA QT connectors
  • ADM : I2C address jumper of the magnetometer
  • AGAD : I2C address jumper of the accelerometer
  • INT1 : Primary interrupt pin (LSM6DS3TR-C chip)
  • INT2 : Primary interrupt pin (LSM6DS3TR-C chip)
  • INTM : Magnetometer Interrupt Pin (LIS3MDL Chip)
  • DRDY : Data ready pin (when measurement data is available, pin shows low)

Detailed information on the module pins and address jumpers sensor can be found in the user manual prepared by Adafruit.

Specification of the gyro accelerometer and magnetometer sensor - Adafruit 5543
  • Developer: Adafruit
  • Manufacturer part number: 5543
  • Supply voltage: 3V or 5V
  • Built-in LED indicating power
  • Accelerometer:
    • Chip: LSM6DS3TR-C
    • Accelerometer measuring range: ± 2 / ± 4 / ± 8 / ± 16 g
    • Gyro measurement range: ± 125 / ± 250 / ± 500 / ± 1000 / ± 2000 dps
    • Supported interface: I2C / SPI
    • ODR: up to 1.6 KHz
    • Double tap and double tap detection
    • Free fall detection
    • Detection of steps / shock
    • I2C address: 0x6A or 0x6B
  • Magnetometer
    • Layout: LIS3MDL
    • Measuring range: ± 4 / ± 8 / ± 12 / ± 16 gauss
    • Continuous and single conversion modes
    • 16 bit data output
    • Interrupt generator
    • I2C address: 0x1C or 0x1E
Kit contents
  • LSM6DS3TR-C + LIS3MDL 9DOF IMU - Adafruit 5543: 1 pc.

An example of a sensor application .

Useful links
  • Manufacturer's website
  • User guide
  • Sample code for Arduino

Доставка

Доставим товар из Германии от поставщика DESTE FZ LLC курьерской службой, в отделение Почты или пункт выдачи в вашем городе. Доставка в Армению, Казахстан, Грузию и Киргизию будет осуществлена доступными службами. Вы сможете выбрать желаемый способ доставки заказа в момент его оформления. Стоимость доставки зависит от выбранного вами метода и составит от 838 руб. Заказ будет доставлен за 10-30 дней, срок зависит от выбранного города. Если вы закажете этот товар прямо сейчас, доставим его 25 мая - 14 июня.

Доставка электроники Adafruit напрямую из Германии в Москву, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие города России осуществляется надежными и проверенными нами службами доставки.

Как только заказ будет отправлен к вам с нашего склада, отслеживание заказа по номеру посылки станет доступным.