Step-Down Voltage Regulator D24V6F9 - 9V 0,6A - Pololu 2108

Бестселлер
43302487
1 459 ₽

Мы выстраиваем выгодные партнерские отношения с поставщиками товаров для строительства и ремонта Pololu и отобрали для вас лучших производителей брендовых товаров из Европы, Америки, Турции и ОАЭ, специализируясь на аутлетах и дискаунтерах. Прямая доставка из-за рубежа до покупателя нашими логистическими решениями — это оптимизированные и экономичные решения, вы не переплачиваете в цене товара за расходы на торговые помещения и шоурумы. Заказ будет отправлен напрямую с нашего склада по указанному вами адресу, по цене недоступной для местных магазинов.

Оригинальные брендовые товары в широком ассортименте с вкусными скидками — так можно описать наш интернет магазин. Доставка заказа будет отслеживаться на всех этапах покупки и работает сразу после оплаты заказа.

  • Бренд Pololu
  • Доставка из Польши
  • Пункт выдачи СДЭК 25 мая
  • Стоимость доставки заказа в Россию от 1 025 ₽

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Напряжение от
42 V
Стабилизатор - Тип
step-down
Стабилизатор - Тип 2
switching
Выходное напряжение от
9.0 V

Вес и размеры

Длина
12 mm
Высота
3 mm
Ширина
10 mm

Общие характеристики

Напряжение до
10.5 V
Выходное напряжение до
9.0 V

Прочие свойства

EAN
5904422330033
Бренд
Pololu
Номинальное выходное напряжение
9.0 V

Энергопитание

Сила тока
0.6 A

Описание

Product description: Polol D24V6F9 - 0.6A step-down 9V 0.6A step-down converter

A step-down converter used to power systems operating at 9 V. The system is designed for a wide range of input voltages from 3.8 V to 42 V (the minimum value depends on thedrop-out voltage).The module allows for current consumption of up to 600 mA, which is sufficient to supply typical integrated circuits. We also offer versions with otheroutputvoltagesand a lowercurrent capacity of up to 300 mA.

D24V6F9 inverter outputs

The module has four outputs:

  • VIN- input voltage from the range of 10.5 V to 42 V, please pay attention to the drop-out value and shortvoltagepulses, which may damagethe system
  • GND- ground potential
  • VOUT -output voltage
  • SHDN -providing a low state (logical zero) causes the system to switch to a low energy consumption state (about 20 uA). In order to start the system it is necessary to provide high state (logical one - voltage above 2.3 V). If the output will not be used, it can be connected to the neighboring VIN pin.

The connectors are properly signed on the board. Outputs' Raster is 2.54 mm (popular goldpin connectors). The module can be plugged into acontactboard,connected with wiresor soldered intoa dedicated PCB.

On customer's request we can deliver a chip with goldpin connectors soldered. For this purpose, please leave the information in the commentary to the order.

Efficiency of the converter system

Efficiency is defined as the ratio of output power to input power (Power out)/(Power in). This is a very important parameter when working with portable energysources(batteries and accumulators), where the time of operation on one charging cycle counts. The efficiency of this pulse system is about 80 % - 90 %.

Inverter drop-out voltage

The parameter referred to in the documentation asvoltag drop-outthennecessary for the proper functioning of the system,minimum difference between input and output voltage.For example, if the drop-out is 1 V and the desired output voltage is 5 V, the supply voltage should be higher than 6 V. The figures below show the dropout voltage value for D24VxFx inverters.

Dangerous voltage pulses

When connecting the power supply to the module, dangerous, short, high amplitude eclectic impulses (so-called pins) may appear, which may permanently damage the system. According to Polol's tests, for voltages above 20V, the pins may have an amplitude of over 42V. In order to protect against this undesirable phenomenon it is recommended to solder a capacitor of at least 33uF as close as possible to the pins powering the converter.

Polol D24V6F9 inverter specification
  • Input voltage: 10.5* V to 42 V
  • Output voltage: 9 V
  • Maximum input current: 600 mA
  • Efficiency of 80 - 90 %
  • Switching frequency 550 kHz
  • Dimensions: 12 x 10 x 3 mm
  • Weight (without connectors): 0.5 g

* minimum value depending on drop-out voltage

Useful links
  • Manufacturer's website - Polol #2108

Доставка

Доставим товар из Германии от поставщика DESTE FZ LLC курьерской службой, в отделение Почты или пункт выдачи в вашем городе. Доставка в Армению, Казахстан, Грузию и Киргизию будет осуществлена доступными службами. Вы сможете выбрать желаемый способ доставки заказа в момент его оформления. Стоимость доставки зависит от выбранного вами метода и составит от 1 025 руб. Заказ будет доставлен за 10-30 дней, срок зависит от выбранного города. Если вы закажете этот товар прямо сейчас, доставим его 14 мая - 3 июня.

Доставка товаров для строительства и ремонта Pololu напрямую из Германии в Москву, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие города России осуществляется надежными и проверенными нами службами доставки.

Как только заказ будет отправлен к вам с нашего склада, отслеживание заказа по номеру посылки станет доступным.