TB67S249FTG Stepper Motor Driver Carrier 47V/4,5A - Pololu 2973

Бестселлер
53153516
2 779 ₽

Мы выстраиваем выгодные партнерские отношения с поставщиками товаров для строительства и ремонта Pololu и отобрали для вас лучших производителей брендовых товаров из Европы, Америки, Турции и ОАЭ, специализируясь на аутлетах и дискаунтерах. Прямая доставка из-за рубежа до покупателя нашими логистическими решениями — это оптимизированные и экономичные решения, вы не переплачиваете в цене товара за расходы на торговые помещения и шоурумы. Заказ будет отправлен напрямую с нашего склада по указанному вами адресу, по цене недоступной для местных магазинов.

Оригинальные брендовые товары в широком ассортименте с вкусными скидками — так можно описать наш интернет магазин. Доставка заказа будет отслеживаться на всех этапах покупки и работает сразу после оплаты заказа.

  • Бренд Pololu
  • Доставка из Польши
  • Пункт выдачи СДЭК 27 мая
  • Стоимость доставки заказа в Россию от 1 022 ₽

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Прочие свойства

EAN
5904422318918
Бренд
Pololu

Описание

Product description: TB67S249FTG - 47 V / 4,5 A stepper motor driver - Pololu 2973

The chip enables steppermotor controlwith a device capable of generatinglogic statese.g.Arduino,STM32Discovoery,Raspberry Pior anymicrocontroller. Pololu module is characterized by verysimple operation. Rising edge of each pulse on CLK (STEP) pinout corresponds to one step. The direction is selected by giving an appropriate state to the CW/CCW (DIR) pin (e.g. low state - clockwise rotation, high state - anticlockwise rotation). The controller can also select theresolution ofmotor operation.

Controller connection

To control a bipolar stepper motor you should connect the system according to the diagram below.

Minimum wiring diagram to connect the microcontroller to the TB67S2x9FTG.

The controller requires a supply voltage from 10 V to 47 V, which will be connected to VIN and GND terminals.

Power supply for the controller

A voltage of 5 V is required to power the logic part of the module, which should be connected to pin VDD. The motor supply voltage from 10 V to 47 V is applied to the VIN pin.

Caution!

Connecting and disconnecting the motor while the controller is on can damage the system.

Resolution and step size

The step size is selected using DMODE0, DMODE1, DMODE2 inputs. The possible settings are shown in the table below. The MS1, MS2 and MS3 inputs have an internal pull-down resistor (100kΩ).

MS1 MS2 MS3 Resolution low low low Standby mode low low high Full step low high low Non-wheeling half step ('a') low high high 1/4 step high low low circular half step ("b") high low high 1/8 step high high low 1/16 step high high high 1/32nd step Controlling TB67S249FTG chip

The rising edge of each pulse on the CLK (STEP) pin corresponds to one step. Selection of the direction is performed by giving the appropriate state on the CW/CCW (DIR) pin (e.g. low state - clockwise rotation, high state - anticlockwise rotation). If the motor is to rotate in one direction only, the DIR pin can be left unplugged.

When the RESET pin goes high, the driver resets its state in the translator array, which outputs to the initial value of 45°. This corresponds to 100% of the current limit on both coils in full step and non-wheel half step modes. The RESET pin does not disable the motor outputs, the controller will continue to supply current to the motor but will not give information to the CLK output

The TB67S2x9FTG can detect several error conditions that report causing one or both LO pins to be low. The manufacturer has includeda table of error combinations on the LO1 and LO2 pinsin thedocumentation.

A detailed description of each pin can be found on themanufacturer's website.

Useful links
  • Manufacturer's website: Pololu #2973
  • TB67S249FTG controller documentation
  • TB67S249FTG/TB67S279FTG information note
  • Circuit diagram
  • Motor connection manual

Доставка

Доставим товар из Германии от поставщика DESTE FZ LLC курьерской службой, в отделение Почты или пункт выдачи в вашем городе. Доставка в Армению, Казахстан, Грузию и Киргизию будет осуществлена доступными службами. Вы сможете выбрать желаемый способ доставки заказа в момент его оформления. Стоимость доставки зависит от выбранного вами метода и составит от 1 022 руб. Заказ будет доставлен за 10-30 дней, срок зависит от выбранного города. Если вы закажете этот товар прямо сейчас, доставим его 16 мая - 5 июня.

Доставка товаров для строительства и ремонта Pololu напрямую из Германии в Москву, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие города России осуществляется надежными и проверенными нами службами доставки.

Как только заказ будет отправлен к вам с нашего склада, отслеживание заказа по номеру посылки станет доступным.