Qwiic OpenLog - data logger - SparkFun DEV-15164

Bestseller
42759674
-5%
108 GEL
Old price 114 GEL
  • Brand SparkFun
  • Shipping from Poland
  • Post delivery June 30
  • Shipping cost for orders to Georgia from GEL 119

Properties

Features

Product Type
Аксессуары для microSD карт

Other features

Brand
SparkFun

Performance

Product Type
Запчасть для микрокомпьютера

Description

Description of product: SparkFun OpenLog Qwiic

The latestversion of the module Qwiic OpenLog is used tosave data onthe microSD card. The main change compared to the previous version are solderedcQwiic connectors, thanks to which you can connect and recorda lot of deviceswithout the need to occupy the I2C serial port. Communication withthe main module (fromany module witha host microcontroller, e.g.Arduino) througha simple serial interfaceorQwiic connector.The modulesupports cards with capacityup to 32 GBwith the file systemFAT16 and FAT32.

What is Qwiic OpenLog data logger for?
  • What are the actual values measured by the sensors?
  • What is the temperature of a closed system, when not monitored?
  • What are the values of the accelerations detected by the accelerometer?
  • Where was the GPS receiver exactly?

All these questions will be answered by OpenLog. Its principle of operation is similar toa black box, used tocollect and storeall data provided by the project.

The set does not containgoldpin connectors 2.54 mm rasterand a cable Qwiic. You can buy them separately and solder yourself.

Microcontroller of OpenLog module

Just like the previous version it has a built-in microcontrollerATmega328 operating with a clock frequency of16 MHz. The ATmega328 has an extinguished bootloaderOptiboot.

Connectors of Qwiic OpenLog module

The main interface of the OpenLog module are Qwiic connectorsonboth sides of the board.

Pins FTDI Qwiic

FTDI pins are used specially for reprogramming the firmware.

SPI Qwiic OpeLog

Six test SPI pins can be used for reprogramming the bootloader on the ATmega328.

MicroSD card slot

For communication, the microSD card requires SPI pins. This is not only a place where data is stored for OpenLog, but you can also update the configuration of the boards using the file config.txt on the microSD card.

LED status of the OpenLog module
  • STAT -Flashes only when the SPI interface is active.
  • PWR- Lights up when a board is enabled and working.
Service of SpakFun Qwiic OpenLog

The device should be connected via the serial interfaceUART or Qwiic- inputs RX and TX. After powerring up and retrieving data from the OpenLog, it will start to record them onthe card. By default, the baud rate is20000 bits. To enter the setup mode, you must load three times the sequencectrl+z,command"new"creates a new file,"md"new folder. The configuration fileconfig.txt,which is located on the memory card can be edited from the computer. This allows you to easily select the mode and to set the transmission speed.

MicroSD memory card not included,you can buy it separately.

The use of the system facilitates a sample programforArduinoanda list of available commands. Users of the module may also use the preparedtutorial. Description and example programs are also available on the GitHub website.

Technical specification of SpakFun Qwiic OpenLog Option Range Input voltage from 3.3 V to 12 V Current consumption
  • Max: 6 mA
  • Standby mode: 2 mA
Serial communication interface UART (RX, TX) Connectors Qwiic Yes 2 x Qwiic Max. speed data logging up to 20,000 bits/sec Compatible with I2C 400 kHz Yes Support for memory cards microSD up to 32GB (sold separately) Address And2C from 0x08 to 0x77 Board size 25 mm x 27 mm x 5 mm

 

Useful links
  • The website of the manufacturer: SparkFun DEV-15164
  • Example program for Arduino
  • Description of the module on GitHub
  • Description of the QWIIC standard
  • Manual
  • Diagram of the module
  • The set of commands
  • Instructions for updating software
  • Sample project
  • Eagle program files